The electrical load a house carries today is nothing like what the same house was wired to handle twenty years ago. Central air running through a hot regional summer, a battery storage system tied to a rooftop solar array, an EV charger in the garage, a workshop on a dedicated circuit: all of that lands on a panel that may have been sized for a fraction of it. C & C Electrical Services handles the full range of residential and commercial electrical work in San Bernardino, from a single tripped breaker to a complete service upgrade that gives a property room to grow. Work is carried out by licensed electricians on every call.
Property managers, business owners, and homeowners across the city all run into the same basic problem: the electrical system has to keep up with what the property actually demands. When it doesn't, we're the call to make. We're available every day from 8:30 AM to 10:00 PM. Call (442) 419-3289 to get a rate on the phone before anything is scheduled.
Homes built in earlier decades were wired for a lighter load, and the panels that came with them reflect that. A 100-amp service that handled a house comfortably for decades runs short when air conditioning, a solar inverter, and a Level 2 EV charger all share the same service entrance. Panel upgrades are one of the most consistent calls we get in San Bernardino, and the reason is almost always the same: the property has outgrown what was installed.
We start every panel assessment with a load calculation. That tells us what the property draws at peak and what headroom a new panel needs to leave for future circuits. A 200-amp service upgrade is the most common outcome, though some properties with larger loads or planned additions need more. Where the utility requires a service-entrance or meter upgrade alongside the panel work, we include that in the scope.
The Inland Empire is one of the stronger residential solar markets in California, and San Bernardino properties reflect that. The electrical side of a solar or battery installation involves wiring from the array to the inverter, battery backup connections, disconnect installation, and the panel capacity needed to carry the system safely. We handle that side of the work, and we make sure the circuits are sized and permitted before the system goes live.
A Level 2 home charger needs a dedicated 240-volt circuit. Before we run one, we check the panel for available capacity and confirm whether an upgrade is part of the job. If the panel has room, we run the circuit and install the outlet or hardwired connection the charger requires. If it doesn't, we handle the upgrade first. The rate is confirmed on the call before anything is scheduled.
The service page carries the full breakdown of what each job involves and what to expect on the day.
Every quote starts with the scope of the job, and the scope depends on what the property actually has. A panel replacement in a newer building is a different job from the same replacement in a property with older wiring that needs to be brought up to code at the same time. A circuit run to a detached garage is priced differently depending on how far the feed has to travel and what the panel can support.
When you call, we talk through what you're dealing with. We ask about the panel, the wiring, and what you're trying to run or fix. From that conversation, we give you a price before anything is scheduled. If the scope changes once the work is underway, we tell you before we proceed. Nothing is added after the fact without a conversation first.
Permits are part of certain jobs, and we handle the documentation where they're required. If a job at your address involves a permit, that's part of what we confirm on the call.
We keep you informed from diagnosis to final test, so you're not left guessing about what was done or what it cost.
Some electrical faults sit inside the home's wiring and panel. Others sit at the meter, the service entrance, or on the utility's side of the connection. The two are not always easy to tell apart from inside the house, and calling the wrong party first costs time.
When we assess a fault, we work from the panel outward. If the problem is inside the home, we diagnose it and quote the repair. If the evidence points to the service entrance or beyond, we tell you clearly and explain what the utility's process looks like from there. We don't charge you to diagnose a fault that turns out to be theirs, and we don't leave you without a clear next step.
Where the utility needs to be involved, we can walk you through what to report and what to expect. The goal is to get the power stable, whatever side of the meter the fault sits on.
A detached garage or workshop that runs power tools, compressors, or EV charging equipment needs more than a long extension cord from the house. A subpanel fed from the main panel gives the structure its own breaker capacity and keeps the circuits clean. We size the subpanel to what the space actually draws, run the feed correctly, and handle the permit where one is required.
Older properties in San Bernardino sometimes still carry knob-and-tube wiring in the walls. That wiring was not designed for the loads a modern household puts on a circuit, and it lacks the grounding that arc-fault and ground-fault breaker protection depends on. We handle knob-and-tube replacement as a targeted repair or as part of a broader rewire, depending on how much of the original wiring remains and what condition it's in.
Running power to a shed, a guest unit, or an electric gate requires a properly sized circuit, the right wiring method for the distance and exposure, and grounding that meets current code. We assess the load, confirm the panel has capacity, and run the supply in a way that holds up over time. Electric gate connections have their own requirements for the control wiring, and we handle those alongside the power feed.
A breaker that trips once and resets is different from one that trips under the same load every time, and both are different from a circuit that goes dead without any obvious cause. Intermittent faults are the hardest to pin down, and they're the ones most likely to be waved off until something more serious happens. We trace faults systematically rather than replacing parts at random, which means the repair addresses the actual problem rather than the most visible symptom.
Outdoor outlets in the region take real punishment from UV exposure and temperature swings. A standard indoor outlet mounted outside fails faster and creates a shock risk when the enclosure degrades. We install weatherproof outlets and in-use covers rated for exterior conditions, with GFCI protection on every circuit that code requires it. Patios, side yards, and outdoor kitchens all fall in this category.
Same-day scheduling is available when the call comes in early enough and the situation calls for it. For a fault that's making part of the house unusable, or an outlet that's warm to the touch, or a breaker that won't hold, we treat that as something that can't wait.
For tenants and businesses that need to stay operational, we work around what the property requires. If a circuit needs to be isolated for part of the job, we confirm that on the call so nobody is caught off guard. If a repair can be staged to keep the rest of the building running, we plan it that way.
We're available every day from 8:30 AM to 10:00 PM. You schedule it. We power it. Simple as that.
We cover San Bernardino and the surrounding communities throughout San Bernardino County. If you're in Muscoy, Rialto, Colton, Loma Linda, or Highland, we cover your address. You're talking to someone who knows the area and the homes in it.
The housing mix across the city and its neighbors varies considerably. Older properties closer to the city center often carry wiring that hasn't been touched since the original installation. Newer construction on the edges of the city tends to have more capacity but still runs into the same panel-sizing questions when solar, battery storage, or EV charging enters the picture. Whatever the property type or the address, the work gets handled the same way.
We work to contain the mess to the area where the work is happening. Drop cloths are used where needed, and we clean up before we leave. If the scope of the work means significant disruption to finished surfaces, we explain that before we start.
A momentary voltage drop when a high-draw appliance starts is common and usually points to a circuit that is shared with too many loads, or a panel that is running close to its capacity. If the dimming is significant or frequent, it is worth having the panel and circuit loading assessed to confirm nothing is being overloaded.
Yes. If the property owner, a property manager, or another party needs a copy of the job documentation, we can direct it accordingly. Let us know on the call who should receive it and we will make sure the right person gets the record.
Yes. An electrical safety inspection covers the panel, wiring, grounding, circuit protection, and outlet condition across the whole property rather than focusing on a single reported problem. It is a practical option for anyone who wants a full picture of the electrical system rather than a targeted repair visit.
Yes. A buyer, a buyer's agent, or any authorized party can schedule an electrical inspection before a transaction closes. We assess the panel, wiring, grounding, and circuit protection and explain what we find so the buyer has a clear picture of the electrical condition before they commit.
If the work requires access to the loft or attic, we need a clear path to reach the area safely. We let you know on the call if access preparation is part of what the job requires, so you are not caught off guard on the day.
Call (442) 419-3289 and tell us what you're dealing with. We'll ask the right questions, give you a rate on the phone, and confirm what it covers before anything is scheduled. C & C Electrical Services is available every day from 8:30 AM to 10:00 PM.
The price is confirmed before we schedule. Nothing changes after the fact without your knowledge and agreement.
We also work in: Rialto, Colton, Highland, Redlands, Fontana. See the whole of our full list of communities.
Below is a quick look at the electrical work we handle across San Bernardino and the surrounding high desert. Every service listed is work we perform on the electrical side: wiring, circuits, panels, and the connections that keep a home or business running. Use this as a starting point, then call us and we will walk through exactly what your job involves.
| Service Type | What's Included | Common Situations | Good to Know |
|---|---|---|---|
| Lighting Installation |
| homeowners adding or replacing interior and exterior lighting | If a fixture is going somewhere it has never been, we run the wiring and confirm the circuit can carry the load before the fixture goes up. |
| Outdoor & Misting-System Circuits |
| patios, outdoor kitchens, and misting systems common in high-desert climates | UV exposure and temperature swings in the high desert affect how outdoor wiring is installed. We match the materials to the environment. |
| Electrical Panel Upgrades |
| homes adding solar, an EV charger, central air, or heavy workshop loads | Every upgrade starts with a load calculation so the new panel is sized for what the home actually draws, not just what it draws today. |
| Solar & Battery Installation |
| San Bernardino homeowners adding solar generation or battery storage | The high-desert sun produces strong generation numbers. We handle the electrical infrastructure so the system is ready to perform safely from day one. |
| Electrical Repairs & Troubleshooting |
| any home or business with an unexplained electrical problem | We trace the fault to its source before touching anything. Swapping parts without a diagnosis often misses the real cause. |
| Pool & Spa Wiring |
| homeowners installing or servicing a pool, spa, or hot tub | Pool and spa wiring carries specific code requirements for bonding and GFCI protection. Work carried out by licensed electricians who know those standards. |
| EV Charger Installation |
| EV owners who want a reliable home charging setup instead of relying on public stations | We check the panel before we run the circuit. If an upgrade is needed first, we include that in the scope so nothing gets undersized. |
| Ceiling Fan Installation |
| rooms without a ceiling fan or with an existing fixture being replaced | A fan that needs a new circuit or a switched outlet where there was none before is a straightforward job when it is set up correctly from the start. |
| Breaker & Fuse Repair |
| homes where a breaker trips under normal load or refuses to reset | A breaker that trips repeatedly is telling you something. The fix may be the breaker itself, or it may be the circuit load. We check both. |
| Electrical Safety Inspections |
| homebuyers, landlords, and owners of older properties | We walk you through every finding before we leave. You will know what was checked, what needs attention, and what is in good shape. |
| Wiring & Rewiring |
| older homes with aging wiring or homebuyers wanting an inspection before closing | We assess what is in the walls before recommending a scope. Not every older home needs a full rewire, and we will tell you honestly what does and does not need attention. |
| RV Hookups |
| homeowners who store an RV and want a proper shore-power connection at home | A properly wired RV hookup uses a dedicated circuit sized for the rig. We confirm the panel has room and run the circuit to the right spot on the property. |
| Outlet & Switch Installation |
| kitchens, bathrooms, garages, and outdoor areas needing code-compliant receptacles | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor locations. We confirm coverage and add it where it is missing. |
| Whole-Home Surge Protection |
| homes with sensitive electronics, solar systems, or older wiring exposed to utility fluctuations | The high desert sees summer lightning activity and periodic utility events. A panel-level unit catches a spike before it reaches any circuit in the home. |
| Dedicated Appliance Circuits |
| homeowners adding a major appliance or workshop equipment | Sharing a circuit with a high-draw appliance causes nuisance trips and can damage the equipment. A dedicated circuit solves both problems. |
Call us at (442) 419-3289 to talk through your job and get a price before anything is scheduled.
(442) 419-3289